SdKfs 250 PARTS
All parts are now available unless otherwise noted
Sd250-01 Frame Antenna $75.00
Sd250-02 Tow Rope Front Mounting $40.00
Sd250-03 Start Crank $20.00 (With new photo-etch fittings)
Sd250-04 Jack Block $35.00
Sd250-05 Stab Antenna Mount $9.00
Sd250-06 Tow Hook $40.00
Sd250-07 MG Travel Lock $18.00 (Not available do to etching fault)
Sd250-08 Grill Covers (Pair) $35.00
Sd250-09m Wire Cutter (Metal) $22.00 (With new photo-etch fittings) (Not available for 2-3 weeks) See note below on size.
Sd250-09p Wire Cutter (Resin) $17.50 (With new photo-etch fittings) See note below on resin
Sd250-10w Shovel (Metal with Wood Handle) $22.50 (With photo-etch fittings)
Sd250-10p Shovel (All resin cast) $17.50 (With photo-etch fittings)
Sd250-11 Pike (Metal) $20.00 (With photo-etch fittings)
Sd250-12m Pick Axe (Metal with Wood Handle) $30.00 (With new photo-etch fittings)
Sd250-12p Pick Axe (All Resin cast) $22.50 (With new photo-etch fittings)
Sd250-13w Small Axe (Metal with Wood Handle) $20.00 (With new photo-etch fittings)
Sd250-13p Small Axe (All Resin cast) $15.00 (With new photo-etch fittings)
Sd250-14m Large Axe (Metal with Wood Handle) $22.50 (With photo-etch fittings)
Sd250-14p Large Axe (All Resin cast) $17.50 (With photo-etch fittings)
Sd250-15 Pry Bar (Metal) $22.50 (With photo-etch fittings)
Sd250-16 Jack and Handle. $80.00
Has ajustable height on thread and turning handle. Not fully functional.
Sd250-17 Tow Rope Side Fitting $55.00 (With photo-etch fittings)
Sd250-18 Convoy Light Sold in Kit form. $20.00. Light back is hollow to allow for the fitting of working light. Color lenses not supplied. Some drilling and taping required.
Sd250-19 Jerry Can Holder. $10.00
Sd250-20 Sternantenna D and Mounting Box $130.00 (Not available for 2-3 weeks)
Gent020 2 Padlocks in Kit form . $10.00 These two miniature padlock are offered in kit form and can be assembled by gluing or sodlering. When assembled correctly the lock will open and close.
More pictures at:
SdKfs 250 Tools and Accessories
Notes
1. For those that have not noticed the front mudguards on the 250 are about an inch to short. This means correct scaled wire cutters will not fit correctly. I have shorten the cutters a little, but the rear mount fitting still has the be fitted to the top of the insert between the front and rear mudguards.
2. New resin cast tools are made of a new resin that is heat cured to 150 degrees, they will not warp in heat and are much stronger that the regular resin used in the past.
3. Those that have already purchased tools Gent13 to 19 and wish to purchase the photo-etch fittings only should contact me for prices indicating which fittings are required.
4. For those that ordered the Gent16 Pick Axe when I first offered it may have a Pick with the head to large to fit the 250 mudguard. Test fit it, if it is to large you may return it for an exchange or simply file it down to the correct size.
Orders will take about one week to fill from payment received.
E-mail orders to:
toyrific@mindspring.com
Regards
Mike Stannard
6th Scale Icons Inc
PO Box 98116
Las Vegas, NV 89193
Tel: 702-523-1172
